Up cycle Pallet Toy Box

For Christmas this year I wanted to make all of my Christmas gifts, I wanted it to be a homemade holiday. My boyfriend also has two adorable nephews H and G, ages one(ish) and two(ish). I decided I wanted to make them a toy box each. I searched pintrest for ideas and sizes because being a mother of two happy rat terriers I had no idea about toddlers, toys and toy boxes. I had many ideas but little experience with children. I figured I would get a rough idea and go with the flow.

My original idea had included a lid, but from talking to my friends with children or friends who have grown children I learned that lids and toddlers do not mix. I tried to find anti-slam hinges but they were ugly, difficult to find and expensive.

After all the designing I put in the request to my  dad for a few pallets and a day later a truck load of pallets arrived in my driveway.

A word on pallets: yes pallets are free or almost free but they do require a lot of effort. You have to find them, haul them home and chop them up. Then when all that is done you have to sand it, sand it and sand it again. So, it would have been easier to go to the hardware store and buy some 1 x 4 or 1 x 6 lumber, but I really wanted the rustic pallet look. So, I began to chop the pallets up.

I used a reciprocating sae to cut the pallets apart. This took a very long time and it took about 25 hours of work per toy box from pallet tear down to finished and ready to paint toy box.

Pallets may be cheap or free but they are labour intensive.

And we begin…

Here are the pallets waiting for me when I got home. Thank-you Dad!

 IMG_0763

I have a plan but when you work with pallets that has to change to suit the materials you have.

I decided on the nice 3/4″ thick boards I found.

 IMG_7313

I made the frames first 24″ x 14″ and held them temporary with brad nails from my air gun.

then I drilled a pilot hole with a bit smaller than my screw and screwed each from together with three screw each.

I used three screwed because these are toy boxes and they need to be tough and take a beating.

 IMG_7331_2    IMG_7330_2

To get the height I stacked the frames together and made sure I had enough wood for the bottom.

This is the point where my wonderful boyfriend sanded each frame section with a palm sander before I assembled the frame sections together.

  IMG_7321_2    IMG_7314

I cut the bottom to fit in between the frames and then secured it with screws from each side.

To hide the screws I frames out the box with 1/4″ x 2″ wooden survey sticks that I had on had from other projects.

I used the wooden survey sticks to attach and hold the frames together.

I buy the survey sticks from any hardware store in the lumber section. I use them for many projects.

     IMG_7333_2

Here are the boxes finished and ready for stain.

 IMG_7338_2          IMG_7341_2

I used Varathane’s Sun bleached wood stain. It is almost like barn-wood and it works great with the pallet board.

I used a brush to coat the box then I rubbed it with a rag to rub it into the grains.

I love the way it turned out! This is my new favourite stain.

 IMG_7345_2   rustolem

Here is a complete side with one coat.

    IMG_7344_2         IMG_7347_2

I used leftover pieces of the survey sticks to put the boy’s initials on the boxes.

I used Minwax wood finish stain in Ebony for the letters and rubbed it in with a rag.

I then took the used rag and rubbed it all over the edges of the box for an aged look.

 IMG_7353_2 IMG_7354_2

I wanted handles and my dad suggested using an old belt.

I could’t find and old belt for cheap but I did find a 6′ length of belt from Tandy Leather Stores, they are a leather supply store found here in Canada.

I got the belt in the scratch and dent bin for next to nothing and it worked perfectly.

I pre drilled holes in the leather then secured them with 1/2″ wood screws with a wide head and used a washer under the head of the bolt to prevent it from pulling through the leather.

IMG_7357_2

And best of all they are 100% Rosie approved!

IMG_7360_2

Thanks for reading and,

HAPPY CRAFTING,

~ Nicole

Two Toned Hutch

Last summer  I was scrounging my favourite spots for furniture and found an aweome deal on a Canadian maple hutch, table and four chairs. It’s candaian made and right out of the 80’s. It’s my exact vintage actually! I knew this would work perfectly in my new place.

I cleaned it out and scrubbed it down. I let it dry and coated it in two coats of white primer. I let it dry 24 hours between coats just to be sure it’s dry. Then I painted it with this lovely shade of grey–it’s a mistint so I can’t tell you the name of the colour. I don’t have any before pictures. I left the inside of the hutch primer white because I like the crispness of the primer against the softness of the grey.

IMG_2216

IMG_2215

 

IMG_2326

IMG_2325

 

And here she sits in my dining room with my other Funky Junky and Interesting Upcyles.

 

Happy Crafting,

~Nicole

Antique Crock Side Table

Crock side table.

 

My dad sent me a picture via text about a crock. I got super excited because I love the old flour stoneware crocks that are floating around the prairies. I especially like to find them for a good price. I got this one and the 2 gallon one, which are both in mint condition.

 

When he sent me the picture I did not full appreciate the size of this crock. When I arrived to pick it up it was huge. I wasn’t even sure it should fit in my mini cooper.IMG_5589

 

Dad found them in the garage of a 72-year-old man who grew up on a farm in Saskatchewan. He and his brother would go everyday and fill it full of water from the well and take back to the farm-house. The crock moved with them as they travelled across the prairies until his family finally settled in Alberta in the early 1970’s.

 

I got this giant beauty home finally. I kept in my front foyer and Rosie decided it was a good place to hide from the thunder.

 

IMG_5427So, Dad and I got out my mini bandsaw and I found a nice piece of pine board in my wood stash and viola! Antique crock side table. I am not worried about it breaking because this is a huge and thick crock. It has survived travel across the prairies and being handled by teenage boys

 

I couldn’t be happier with how it turned out. Now I need to decide what colour to stain it. Should I go barn board grey? Vintage Singer sewing machine red or something completely different?IMG_2332 IMG_2331